Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1 Manual de usuario descargar pdf (Pagina 19)

www.johnsonsystems.com 19

10. DMXB TRM Enable or disable termination on the DMX B input.

Activates and deactivates a 120Ω termination resistor. DMX termination is indicated

on the LCD display when DMX is being received. When the DMX B input is not

terminated (DISABLED) the LCD display will read AXXXBXXX. When the DMX B

input is teminated (ENABLED) the LCD display will read AXXX

XXX.

ENABLED Press EXECUTE to toggle termination from ENABLED to DISABLED.

DISABLED Press EXECUTE to toggle termination from DISABLED to ENABLED.

Any change in the conguration is automatically saved.

NOTE: Ensure only the last (end-of-line) DMX receiving device is terminated!

11. DMX O/P Congure the on-board DMX protocol manager for offset or patch mode..

OFFSET mode is typically used for the majority of systems, and is the factory default.

OFFSET mode refers to the DMX start address, with each of the 24 dimmer (PWM)

outputs addressed sequentially from the DMX start address.

PATCH mode provides full exibility for addressing each of the 24 dimmer (PWM)

outputs. Each of the 24 dimmer (PWM) outputs can be patched to (controlled from)

any DMX input channel from 001 to 512, from either or both of the DMX A and DMX B

inputs simultaneously

With DMX patch mode activated, any conguration within the ADDRESS, DMX

MODE, 2 RM SET and DC PATCH menus is ignored, and the DMX patch congured

within the DMXA PAT and DMXB PAT menus takes precedence.

When using the system in DMX patch mode, it is strongly recommended to printout

the patch using a hand held infrared printer (Johnson System Inc., Part Number: JS-IP).

Press EXECUTE to enter the menu and congure the DMX mode.

DISABLED This menu is disabled to help prevent inadvertent changes. Proceed to enable.

ENABLED Press and hold MENU ( ) and MENU ( ) at the same time for 4-5 seconds.

OFFSET Press EXECUTE to toggle the DMX mode from OFFSET to PATCH.

PATCH Press EXECUTE to toggle the DMX mode from PATCH to OFFSET.

Press ESCAPE or RESET to exit the menu.

Any change in the conguration is automatically saved.

12. DMXA PAT Patch the 24 dimmer (PWM) outputs to any DMX A input channel.

There are two ways to congure the DMX patch. Each of the 24 dimmer (PWM)

outputs can be manually (MANUAL) patched to a DMX input channel, or patched in

blocks (BLOCK) of sequential dimmers and DMX channels.

For MANUAL patching, each of the dimmers are patched individually. First, the

dimmer (DIM) output is selected, and then any DMX input channel from 001 to 512 is

patched to the selected dimmer.

For BLOCK patching, a sequential range of dimmers are patched to a sequential

range of DMX channels. First, the rst dimmer number (DIM#) in the block is selected,

then the DMX A start address (DMXA) for the block is selected, and then nally the

number of dimmers (#DIM) in the block is selected. For example, if DIM# is 001, DMX

is 001, and #DIM is 024, then all of the dimmer outputs, 001 thru 024 are addressed

sequentially to DMX channels 001 thru 024.

For a more complex example, if DIM# is 007, DMX is 321, and #DIM is 012, then

dimmer outputs 007 thru 018 are addressed sequentially to DMX channels 321 thru 344.

Using a combination of MANUAL and BLOCK patching methods can speed up

conguration. Typically, a BLOCK of dimmers is rst patched and then edited using

the MANUAL patch.

The DMX patch should be cleared (CLEAR) before conguring the patch. Clearing

the patch ensures all previously congured patch data is cleared (erased).

When DMXA PAT is utilized in conjunction with DMXB PAT, each of the 24 dimmer

(PWM) outputs can be patched to (controlled from) any DMX input channel from 001

to 512, from either or both of the DMX A and DMX B inputs simultaneously.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 33 34

Comentarios a estos manuales

Sin comentarios

Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1 Manual de usuario Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1