Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1 Manual de usuario descargar pdf (Pagina 10)

www.johnsonsystems.com

J24

J23

J18

J17

J33

J30

J29

J28

J27

J26

J21

J20

J19

J16J15

PS1

J8J7 J10J9

J12

J11

J14J13

J32

INPUT

VAC26485

WATTS15DCVOLTS12SUPPLYPOWER

AUX

SCTY

FIRE

OCOP

+12V

COM

ANA4

ANA3

ANA2

ANA1

COM

BCN

D-

D+

D-

D+

D-

D+

DMX A I/ODMX B I/O

BUMP

REMOTE

LCD AND LED STATUS

D-

A-

B-

C-

D-

UAD

SSR1

UAD

SSR2

DUAL

SSR1

DUAL

SSR2

UAD

SSR3

FAN1 FAN2

A-

B-

C-

D-

A-

B-

C-

D-

A-

B-

C-

D-

A-

B-

C-

D-

A-

B-

C-

D-

TERMO

TEMP

SENSOR

-STAT

LM35DT

FAN3 FA N4

UAD

SSR4

UAD

SSR5

UAD

SSR6

DUAL

SSR3

DUAL

SSR4

DUAL

SSR5

DUAL

SSR6

DUAL

SSR4

DUAL

SSR5

DUAL

SSR6

1210 620

1210 6201210 620



Signal Distribution Board

JS-ICON

™

MAINTAINED

NORMALLY OPEN

SWITCH CONT

ACT

+12V

ANA1-4

Control Input/Output

JS-ICON

™

Series dimmer racks come with a variety of control input and output

(I/O) capabilities. All I/O connections are terminated on the Signal Distribution

Board, located on the right-hand side of the dimmer rack.

Breakaway type connectors are supplied for all I/O connections.

• Use wire size #28 to #12 AWG. Strip insulation length to 0.3" (7.5mm).

• Torque terminations to 3.6 IN-LBS (0.4 NM).

NOTE: For connection use copper wire only, rated for 167°F (75°C) minimum.

Dual DMX Input and Through

• DMX A terminates to J7 and J8 connectors.

• DMX B terminates to J9 and J10 connectors.

• Complies with USITT DMX512-A (ANSI E1.11 - 2008), Standard protocol

for digital data control.

• Recommended cable is Belden 9829, 9842, Cat 5 or equivalent

(low-capacitance, twisted pair).

• Wiring must follow a daisy-chain topology.

• Maximum of 32 receiving devices on a single DMX line.

• Maximum cable length is 1,500 feet (455 meters).

• For more information, Google DMX, or visit:

http://old.usitt.org/DMX512FAQ.aspx

NOTE: Ensure only the last (end-of-line) DMX receiving device is terminated!

Models JS-ICON

™

Rx and JS-ICON

™

Wireless DMX is optional for all JS-ICON

™

Series dimmer racks. SHoW DMX

receiver (JS-ICON

™

Rx) and transmitter (JS-ICON

™

Tx) is sourced from City

Theatrical, and has been selected for its reliability and ease of use. The JS-

ICON

™

Rx is specically designed for easy adaptation to all JS-ICON

™

products.

The JS-ICON

™

Rx comes complete with a wiring harness and mounting

hardware. For more information visit:

http://www.johnsonsystems.com/JS-ICON_Rx_Manual_by_City_Theatrical.pdf.

+12VDC Power Supply Output

• A regulated +12VDC power supply is available for powering external

devices.

• Terminate on +12V and COM of J12 connector.

• External devices should not exceed the maximum combined current draw

of 200mA.

0-10VDC Analog Inputs or Load Shed Contact Inputs

• Four (4) analog inputs terminate on J12 connector.

• AN1=Analog Input 1, AN2=Analog Input 2, AN3=Analog Input 3,

AN4=Analog Input 4.

• Inputs can be congured for normal or load shed mode of operation.

• Inputs can be patched to any combination of dimmer output circuits.

•

Programmed in the “ANA MODE” and “ANA PTCH” menus. See page 22 for details.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 33 34

Comentarios a estos manuales

Sin comentarios

Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1 Manual de usuario Pagina 10

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1