Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1 Manual de usuario descargar pdf (Pagina 16)

www.johnsonsystems.com

Detailed Programming of System Conﬁguration Menu Items

NOTE: The programming switches can be locked out to prevent inadvertent conguration

changes. To toggle between “LOCKED!!” and “UNLOCKED” press and hold down the EXECUTE

and then ESCAPE switches at the same time for 4-5 seconds.

The sequence of the following system conguration menu items appear as the MENU DOWN ( ) switch

is pressed. Pressing the MENU UP ( ) switch will sequence the system conguration menu items in the

opposite order. Pressing and holding either of the MENU UP/DOWN ( ) switches will speed up the scroll

rate, which can be helpful to speed up the conguration time.

1. SCENESET Enable and setup 24 different backup scenes.

When scene mode is activated the selected scene will be held with no timeout until

the menu is exited. The 24 control channel levels are congured within the menu and

can be modied on the y. Scene mode is useful when an external controller is not

available and independent internal control is required.

Press EXECUTE to enter the menu and activate scene mode.

SCENE>01 Displays the scene (01) to be activated.

SCENE>24 Press MENU ( ) to select a different scene from 01 to 24.

CTRL: ON Control (CTRL) is ON via the selected scene.

CTRL:DMX Control (CTRL) is via DMX and takes priority over scene mode.

CTRL:HLD Control (CTRL) is via DMX status hold (HLD) and takes priority over scene mode.

SCENE>24 Press EXECUTE to activate the selected scene.

SCENE:24 The colon (:) ashes twice per second while fading to the selected scene.

SCENE:24 The colon (:) stops ashing when fade is complete and the selected scene is active.

SCENE>24 Press MENU ( ) to select a different scene from 01 to 24.

SCENE 24 Press EXECUTE to modify the selected scene.

C>01L 00 The second line on the LCD indicates the control channel (C) and level (L).

C>24L 00 Press MENU ( ) to select the control channel (C) to modify from 01 to 24.

C 24L>00 Press EXECUTE to toggle from channel (C>) to level (L>) selection.

C>24L 00 Press ESCAPE to toggle from level (L>) to channel (C>) selection.

C24L>FL Press MENU ( ) to select the output level (L) for the selected channel from 00 to FL.

CLEAR??? Press EXECUTE to clear the selected preset, and set all channels to 00 level.

SURE ??? Press EXECUTE if you are sure to clear the selected preset.

DONE !!! Indicates the selected preset has been cleared.

WAIT... Press ESCAPE to exit and the menu and save programmed scene levels.

Press ESCAPE to back-up within the menu, or exit/deactivate scene mode.

Press RESET to exit scene mode without saving programmed scene levels.

NOTE: When scene mode is activated: DMX and DMX status hold (SH TIME)

automatically takes precedence over scene mode. The analog input levels are

merged (HTP) with the scene levels. If the analog inputs are congured for load

shed mode the inputs will take precedence over the active scene. The security

alarm (S-ALARM) input is merged (HTP) with the scene levels while the re alarm

(F-ALARM) input automatically takes precedence. The local buttons (L-BUTTONS)

are temporarily set for scene mode and the auxiliary input (AUX IN) is enabled.

Scene mode will only activate dimmers assigned to room “A”.

2. FADETIME Set the fade time for each of the 24 scenes from 0 to 99 seconds.

The factory default is 5 seconds for all 24 presets.

Press EXECUTE to enter the menu.

S>01T 05 Displays the scene (S>01) and assigned fade time (T 05).

S>24T 05 Press MENU ( ) to select a different scene from 01 to 24.

S 24T>05 Press EXECUTE to toggle between scene (S>) and fade time (T>) selection.

S 24T>99 Press MENU ( ) to select a different fade time from 00 to 99 seconds.

Press ESCAPE to exit the menu and save the selected fade time.

Press RESET to exit the menu without saving.

The menu will automatically timeout after 2 minutes of inactivity and save.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 33 34

Comentarios a estos manuales

Sin comentarios

Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1 Manual de usuario Pagina 16

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Johnson-systems JS-ICON Series Dimmer/Relay Rack (2410,2413,1220,1