Johnson-systems EDI-120 Control Retrofit Manual de usuario descargar pdf (Pagina 22)

www.johnsonsystems.com

Press EXECUTE to enter the menu and congure the DMX mode.

DISABLED This menu is disabled to help prevent inadvertent changes. Proceed to enable.

ENABLED Press and hold MENU ( ) and MENU ( ) at the same time for 4-5 seconds.

OFFSET Press EXECUTE to toggle the DMX mode from OFFSET to PATCH.

PATCH Press EXECUTE to toggle the DMX mode from PATCH to OFFSET.

Press ESCAPE or RESET to exit the menu.

Any change in the conguration is automatically saved.

12. DMXA PAT Patch the 120 dimmer (PWM) outputs to any DMX A input channel.

There are two ways to congure the DMX patch. Each of the 120 dimmer (PWM)

outputs can be manually (MANUAL) patched to a DMX input channel, or patched in

blocks (BLOCK) of sequential dimmers and DMX channels.

For MANUAL patching, each of the dimmers are patched individually. First, the

dimmer (DIM) output is selected, and then any DMX input channel from 001 to 512 is

patched to the selected dimmer.

For BLOCK patching, a sequential range of dimmers are patched to a sequential

range of DMX channels. First, the rst dimmer number (DIM#) in the block is selected,

then the DMX A start address (DMXA) for the block is selected, and then nally the

number of dimmers (#DIM) in the block is selected. For example, if DIM# is 001, DMX

is 001, and #DIM is 120, then all of the dimmer outputs, 001 thru 120 are addressed

sequentially to DMX channels 001 thru 120. For a more complex example, if DIM# is

061, DMX is 321, and #DIM is 030, then dimmer outputs 061 thru 091 are addressed

sequentially to DMX channels 321 thru 351.

Using a combination of MANUAL and BLOCK patching methods can speed up

conguration. Typically, a BLOCK of dimmers is rst patched and then edited using

the MANUAL patch.

The DMX patch should be cleared (CLEAR) before conguring the patch. Clearing

the patch ensures all previously congured patch data is cleared (erased).

When DMXA PAT is utilized in conjunction with DMXB PAT, each of the 120 dimmer

(PWM) outputs can be patched to (controlled from) any DMX input channel from 001

to 512, from either or both of the DMX A and DMX B inputs simultaneously.

If a dimmer is patched to both DMX A and DMX B input channels, the DMX levels are

merged and highest-takes-precedence (HTP).

Press EXECUTE to enter the menu and congure the DMX A patch.

Press MENU ( ) to scroll through and select the patching method.

MANUAL? Press EXECUTE to patch each of the dimmers manually (MANUAL).

DIM DMXA The top line shows the dimmer (DIM) and (DMXA) address headings.

001<999? The second line shows the dimmer (DIM) and (DMXA) address values.

120<999? Press MENU ( ) to select the dimmer (DIM) from 001 to 120 to patch.

001<999? Press MENU ( ) and MENU ( ) at the same time to toggle back to 001.

001 999? Press EXECUTE to advance and select the DMXA address for the dimmer.

001 999? DMXA is initialized at 999 to indicate the dimmer is not patched.

001 999? ? indicates the DMXA address (513 to 999) is invalid and is not patched.

001 999? The cursor (_) position indicates the DMXA digit to be edited.

001 999? Press EXECUTE to move the cursor to the right, under the digit to be edited.

001 999? Press ESCAPE to move the cursor to the left or to exit the menu.

001 512 Press MENU ( ) to select the DMXA address from 001 to 512.

001 999? Press MENU ( ) and MENU ( ) at the same time to toggle back to 999.

Repeat until all required dimmers are manually patched.

BLOCK? Press EXECUTE to patch the dimmers in a sequential block (BLOCK).

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 35 36

Comentarios a estos manuales

Sin comentarios

Johnson-systems EDI-120 Control Retrofit Manual de usuario Pagina 22

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Johnson-systems EDI-120 Control Retrofit